American Standard 2590.801.002 Guida di Installazione Scaricare il pdf

SLOT

MOUNTING

SURFACE

Turn off hot and cold water

supplies before beginning.

CAUTION

Insert SPOUT (1) and CABLE CONNECTOR (2) through center hole, making sure

the SEAL WASHER (3) is properly seated.

Assemble RUBBER WASHER (4) with BRASS WASHER (5) and LOCKNUT (6) onto SPOUT

SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting

hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.

Tighten LOCKNUT (6) ﬁrmly. Fig. A.

Tighten LOCKNUT (11) with WRENCH (8) (supplied) to secure VALVE

BODY (13). Repeat above steps for opposite VALVE BODY (13A).

Install LOCKNUT (11) and RUBBER WASHER (12) onto VALVE BODY (13).

From under side of mounting surface, install VALVE BODY (13) through valve

mounting holes. Threads of VALVE BODY (13) should extent at least 5/16

of a inch above mounting surface top. Fig. B. Thread ADAPTER (10)

onto VALVE BODY (13) until snug against internal stop. If necessary, adjust

LOCKNUT (11).

2590.801

Certiﬁed to comply with ANSI A112.18.1

Installation

Instructions

STUDIO

Spread Lavatory Faucet with

INSTALL SPOUT

INSTALL VALVE BODY

13a

Place RUBBER RING (9) into ADAPTER (10).

5/16'' MIN.

Speed Connect™ Drain

Adjustable Wrench Screwdriver Channel Locks

Recommended tools

Tubing Cutter

Fig. A.

Fig. B.

M968625 Rev.1.1

Congratulations on purchasing your American Standard

faucet with Speed Connect drain, a feature found only on

American Standard faucets.

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Speed Connect™ Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the ﬁrst time, every time.

1 2 3 4 5 6

Sommario

Pagina 1 - Instructions

4625SLOTMOUNTINGSURFACETurn off hot and cold watersupplies before beginning.CAUTIONInsert SPOUT (1) and CABLE CONNECTOR (2) through center hole, makin

Pagina 2 - REAR OF SINK

2 61POP-UP KNOB (1) must be fully down. Fig. B. FLANGE GASKET AND POP-UP KNOBFig. A.Fig. B.Check DRAIN FLANGE in SINK to ensure thatWHITE FOAM GASKET

Pagina 3 - ATTACH CABLE CONNECTOR

Connect HOT water supply to inlet of left SHANK and COLDwater supply to right SHANK using sealant, appropriateconnectors, and COUPLING NUTS.Connect 1-

Pagina 4 - M968625 Rev.1.1

10INSTALL HANDLESCHECK DRAIN CONNECTIONS11121314TEST INSTALLED FITTINGWith HANDLES (1) in OFF position, turn on WATERSUPPLIES (2) and check all connec

Pagina 5 - Speed Connect™ Drain

Fig. F.5Speed Connect™ DrainTroubleshooting GuideDisconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.Lo

Pagina 6

LOOP TOWARDREAR OF SINKLOOP TOWARDFRONT OF SINKFig. G.180˚LOGOLOGODRAINFig. H.STOPPER INSTALLATION PROCEDURELocked Mode: Look at the Plastic Loop at t

Commenti su questo manuale

Nessun commento

American Standard 2590.801.002 Guida di Installazione

Navigare online o scaricare Guida di Installazione per Prodotti sanitari American Standard 2590.801.002. American Standard 2590.801.002 Installation Guide Manuale Utente

Sommario

Commenti su questo manuale

Prodotti e manuali riguardandi Prodotti sanitari American Standard 2590.801.002